Parts Counting Scales

    A counting scale determines piece count by dividing total weight by an average piece weight learned from a sample. Accuracy depends far more on piece-weight consistency and internal counting resolution than on the displayed weight increment, which is why counting scales quote a separate internal resolution such as 1/1,000,000.

    Also called: parts counting scale · inventory scale · piece counting scale · coin counting scale

    Counting Scales in stock

    Shipped from the United States with the manufacturer's warranty. Prices shown are current US pricing; call 832-290-3120 for volume quotes or application help.

    Loading counting scales…

    How counting scales work and how to specify them

    The sampling step is where counting goes wrong. If you sample 10 pieces on a scale whose displayed increment is coarse relative to a single part, the average piece weight carries an error that is then multiplied across the whole container. Sample 50 or 100 pieces where possible, and use the scale's sample-refresh or accumulate function so the average improves as more pieces are added.

    The second failure mode is part variation. Stamped and molded parts vary by a few percent piece to piece; plated, oiled or mixed-lot parts vary more. No counting scale can be more consistent than the parts themselves, so for high-value counts split by lot rather than mixing.

    For large counts, use a two-scale setup: a high-resolution balance to establish the average piece weight and a higher-capacity counting scale to weigh the bulk container. Every instrument can ship with a NIST-traceable calibration certificate performed in our Cypress, Texas service lab, and we handle on-site calibration and repair across the Houston metro.

    Counting scale selection

    Counting scale selection
    ApplicationTypical capacityTypical readabilityNotes
    Electronics, small hardware, jewelry findings1.2–6 kg0.01–0.1 gCompact balance with count mode
    Fasteners, kitting, stockroom counts6–30 kg0.1–1 gDedicated counting scale
    Bulk bins and totes60–150 lb0.005–0.01 lbBench counting platform
    Two-scale remote countingBase + remoteCombinedSample on the fine scale, bulk on the coarse

    What to check before you buy

    • Lightest piece weight. One piece should weigh at least 10 display divisions on the scale doing the sampling.
    • Internal counting resolution. Look for the internal figure (e.g. 1/1,000,000), not the displayed increment.
    • Sample size options. 5/10/25/50/100-piece sampling plus automatic average refinement.
    • Memory. Stored piece weights for repeat SKUs remove the sampling step entirely.
    • Capacity for the container. Include the bin or tote weight — tare does not give capacity back.

    Counting Scales buyer's guide: how to choose the right model

    Work through these criteria in order. Each one narrows the shortlist, and getting them in this sequence is what prevents an expensive mismatch between the instrument and the job.

    1. 1. Confirm counting scales are the right class

      You need piece counts, not just weight. Bench platform with piece-weight counting firmware. If that does not describe your job, the wrong class will cost you twice — very light parts where a single piece weighs less than the display increment.

    2. Key criterion 1

      The rule of thumb: readability must be finer than the lightest single piece, ideally 1/3 of it.

    3. Key criterion 2

      ACAI or equivalent sample refinement dramatically improves accuracy on mixed-weight parts.

    4. Key criterion 3

      Store piece weights in memory if you count many part numbers each shift.

    5. Key criterion 4

      A second remote display speeds two-person kitting lines.

    6. 2. Size the capacity with headroom

      This class runs 3 kg – 30 kg. Work from your heaviest realistic load including packaging, pallet or container, then step up to the next capacity rather than running an instrument at its ceiling every day.

    7. 3. Set readability from the smallest thing you measure

      Typical readability here is 0.1 g – 1 g. Choose resolution from the smallest increment you must resolve — not the largest weight — and remember that finer resolution means a slower, more environment-sensitive reading.

    8. 4. Match the instrument to the environment

      Kitting, inventory, hardware and fastener handling. Decide on washdown rating, mounting and display position before comparing prices; an under-specified enclosure is the most common reason a scale is replaced early.

    9. 5. Decide whether it must be legal for trade

      Rarely required — counting is an internal calculation. If money changes hands on the basis of the weight, you need an approved model sealed by your state weights-and-measures authority; if it is an internal process check, you do not.

    10. 6. Plan data, service and calibration

      Choose the data path you will actually use — printout, serial, USB or PLC — and budget annual calibration. We calibrate, certify and repair counting scales in our Cypress, Texas lab and on site across the Houston metro.

    Counting Scales vs Bench Scales vs Lab Balances vs Industrial Scales

    These categories overlap in capacity but not in how the load is presented. Compare the rows below, then follow the link to the category that matches your application.

    Counting Scales vs Bench Scales vs Lab Balances vs Industrial Scales — selection comparison
    CategoryHow it takes the loadTypical capacityTypical readabilityUse casesChoose it whenLegal for trade
    Counting Scales (this page)Bench platform with piece-weight counting firmware3 kg – 30 kg0.1 g – 1 gKitting, inventory, hardware and fastener handlingYou need piece counts, not just weightRarely required — counting is an internal calculation
    Bench ScalesBench-top platform with a separate or integral indicator10 lb – 500 lb0.001 lb – 0.1 lbPacking benches, production cells, receiving desksOne person can lift the item onto a waist-height platformNTEP versions widely available
    Lab BalancesBench balance with draft shield on finer models120 g – 8 kg0.001 g – 0.1 gQC labs, pharmacies, universities, production labsYou need milligram or centigram resolution with GLP outputNTEP versions available where sales by weight occur
    Industrial ScalesAny rugged production-floor weighing platform or system50 lb – 20,000 lb0.1 lb – 5 lbManufacturing, recycling, agriculture, logisticsThe scale lives on a production floor and must survive itNTEP available across most industrial classes

    Certifications, datasheets and documentation

    What we can certify for counting scales, and the documents you can download before you raise a purchase order.

    • Authorized A&D Weighing dealer

      Sold as an authorized dealer since 1998, so every unit carries the full manufacturer warranty and factory firmware — not grey-market stock.

    • NIST-traceable calibration certificate

      Any instrument can ship with a calibration certificate produced in our Cypress, Texas lab using mass standards traceable to NIST, with as-found and as-left values recorded.

    • NTEP legal-for-trade options

      Models in this category are available with an NTEP Certificate of Conformance evaluated against NIST Handbook 44, ready for sealing by your state weights-and-measures authority.

    • ASTM E617 / OIML R111 test weights

      Verification weights are supplied in ASTM Class 1–6 or OIML E2–M3 tolerances, sized so the standard's tolerance stays inside one third of the scale's smallest division.

    • In-house repair & on-site service

      Factory-trained technicians repair, adjust and re-certify weighing equipment in our own Texas workshop and on-site across the Houston metro.

    Counting Scales — specification datasheet (PDF)

    Capacity and readability selection table, buying criteria, certification notes and the answers to the questions purchasing always asks — two pages, no email required.

    Download datasheet

    Instruction manuals hosted here

    All scale manuals and literature

    Counting Scales glossary — the specification terms explained

    Every term used in the tables above, defined the way NIST Handbook 44, ASTM E617 and OIML R76/R111 use it.

    Accuracy
    How close a displayed weight is to the sample's true mass. Accuracy is limited by readability, repeatability and linearity together, so a scale can never be more accurate than its specification sheet's worst of those three figures.
    Auto-zero tracking
    A function that continuously re-zeros small drifts near zero so the display stays at 0 when the pan is empty. It can mask a very slow addition of material, so it is disabled for some dispensing work.
    Calibration
    Adjusting a scale's span so it reads a certified test weight correctly, documented with as-found and as-left values. Distinct from verification, which records a reading without changing anything.
    Capacity
    The maximum mass a scale is rated to weigh. Usable capacity is the rated capacity minus every container, fixture or platform that sits on the pan, because tare does not add capacity back.
    Counting mode
    A mode that divides total weight by a sampled unit weight to report piece count instead of mass. Count accuracy depends on how many display divisions the single lightest piece weighs — at least ten is the practical minimum.
    Division (d)
    The smallest increment the display can change by, also called readability or scale interval. A 1200 g x 0.01 g balance has a 0.01 g division and 120,000 divisions across its range.
    Linearity
    The maximum deviation from a straight line between zero and full capacity, expressed in divisions. A balance can be perfectly repeatable and still be non-linear, which is why calibration is checked at more than one point.
    NIST traceable
    A calibration performed with standards whose values link through an unbroken chain of comparisons, each with stated uncertainty, back to national standards held by NIST.
    Readability
    The smallest increment a display can show. Readability is not accuracy: it sets the finest digit you can read, while accuracy also depends on repeatability and linearity.
    Repeatability
    The standard deviation of repeated weighings of the same load under identical conditions, quoted in grams or divisions. It sets the practical floor on how small a difference you can trust.
    Resolution, internal
    The number of counts the analog-to-digital converter actually resolves internally, typically ten to a hundred times finer than the displayed readability. High internal resolution is what makes stable, fast display averaging possible.
    Stabilisation time
    How long after a load is applied before the reading is stable enough to record. It determines real throughput far more than capacity does in high-volume weighing.
    Full scale glossary — every weighing term defined

    Counting Scales — frequently asked questions

    How accurate is a counting scale?
    Counting accuracy is limited by piece-weight variation, not the scale. With consistent parts and a 100-piece sample, ±0.5% counts are realistic; with mixed-lot or plated parts, error grows quickly.
    How do I improve counting accuracy?
    Sample more pieces, use a scale with finer readability for the sampling step, count one lot at a time, and re-sample when the part supplier or plating changes.
    Can a regular scale count parts?
    Only if it has a counting mode. Any balance can approximate counting by dividing total weight by piece weight manually, but dedicated counting scales apply automatic average refinement that manual division does not.
    What is average piece weight (APW)?
    APW is the mean mass of one item, learned by weighing a known sample quantity. All piece counts are total weight divided by APW, so APW error scales directly into count error.